Staleks Pro EXPERT diamond cutter, red oil, diameter 2.5 mm / working part 5 mm (FA130R025/5)

Staleks diamond cutter olive EXPERT red working part 5 mm - a fine abrasive tool with diamond coating for delicate skin treatment. The oil form processes the cuticle, side ridges, works with calluses without the risk of skin injury. Suitable for beginners and experienced nail masters.

The manicure cutter is produced by spraying diamond grit onto a metal blank made of medical grade stainless steel. Fine-grained diamond grains are applied: they evenly and densely cover the entire working area without gaps or sticking in one place. The grit is fixed on the blank as a result of a galvanic process: a thin layer of nickel holds the diamond grains, making the connection strong and durable.

This spraying technology makes the tool hard and wear-resistant, eliminates unevenness on the surface of the working area. Due to the high quality of the diamond chips, the attachment will last longer, and its rotation center does not shift when working at high speeds of the milling cutter.

What is the olive cutter used for? It lifts and removes cuticles, processes lateral ridges and sinuses around nails, and processes cracks and calluses in pedicures.

Staleks EXPERT manicure cutter with red notch diameter 2.5 mm soft hardness. It is safe when used correctly and is suitable for beginners and experienced nail masters.

The shank diameter is standard for a milling machine – 2.36 mm +0/-0.016 mm. The maximum permissible rotation speed of the diamond attachment is up to 30,000 rpm. It is important to follow the recommendations for the number of revolutions for each type of cutter and procedure – working at high speeds can cause the cutter to overheat and injure the client.

Optimal speed for performing manicure procedures:

• Natural nails and skin, thousand rpm: 5-10 - filing, reducing thickness, grinding, polishing; 10-15 - removing cuticles, grinding side ridges.
• Artificial nails, thousand rpm: 15-20 - thickness removal, shaping; 20-25 - coating removal, design; 25-30 - free edge formation; more than 30 - individual types of design, other work.
• Pedicure, thousand rpm: 5-15 - removal of corns, skin polishing; 15-25 - cleaning cracks, removal of superficial calluses; 25-30 and more - work with core calluses, other types of work.

The milling cutter oil is resistant to corrosion and can be sterilized and disinfected in various ways, except for the use of disinfectant solutions based on active oxygen.

Staleks diamond cutter olive EXPERT red working part 5 mm.

• purpose: hardware manicure and pedicure;
• form: vegetable oil;
• base material: stainless steel;
• high quality diamond coating;
• notch: red;
• abrasiveness: fine;
• hardness: soft;
• size of the working part: length – 5 mm, diameter – 2.5 mm;
• recommended speed: up to 30 thousand revolutions per minute;
• service life: 3-4 months;
• corrosion resistance;
• withstands all types of disinfection and sterilization;
• in a package: 1 pc.

Staleks EXPERT manicure cutter with red notches, diameter 2.5 mm.

1. Choose a tool based on the type of area being treated: cuticle oil cutter, grinding, length cutting, etc. It is also important to follow the recommended number of revolutions for a specific cutter to avoid overheating the tool and injuring the client.
2. Do not throw or hit the attachment - this may cause the rotation center to shift and lead to defects. A deformed cutter cannot be used.
3. Check the alignment regularly, either visually or with a special tool.
4. When working, use gloves, safety glasses or a shield.

Cleaning diamond bits

Staleks can withstand all types of disinfection and sterilization (cold or hot).

• Remove the handle of the device immediately after use. Using a soft brush, carefully remove any remaining nail dust and other dirt. Try not to scratch the surface of the nozzle to avoid damage.
• To remove light dirt from the attachments, it is not recommended to wash them with running water using a brush, so as not to splash drops with possible pathogens.
• Disinfection: Prepare a disinfectant solution and place the attachments in it, following the manufacturer's instructions for time and concentration. It is recommended to choose products that destroy hepatitis B, C and dermatomycosis viruses.
• Use a container with warm soapy water and a mild detergent. Dip the cutter in the solution for 10-15 minutes to soften the remaining dirt. You can use an ultrasonic bath for a deeper pre-sterilization cleaning.
• Sterilization. Place the tips in sterilization bags intended for tendon or autoclave containers to avoid damage and ensure proper air or steam circulation. at 180°C for 60 minutes, 160°C for 150 minutes.
• Autoclave sterilization time: at 120°C, 1.1 atm. pressure for 45 minutes; 132°C, 2 atm. pressure - 20 minutes. After autoclave sterilization, it is recommended to leave the instrument for 1 hour to cool down, so that sudden temperature changes do not damage the nozzle.
• Regularly check the autoclave or tendon performance with biological indicators to ensure sterilization is effective.

Storage of diamond bits

• Store the attachments clean and dry in a sterile, closed container. Choose a dry storage location to prevent rust and mold.
• Avoid getting moisture, dust, and abrasives between the working surfaces of the cutters.

When to change the tool

If diamond bits are used, stored and cleaned correctly, their functionality will remain for 3-4 months. The metal will not be covered with corrosion, and the diamond coating will be uniform, without gaps. There should be no burrs or chips on the tip of sharp shapes.

When it's time to change attachments:

1. The working area has lost its abrasiveness, has become smooth in places or has become clogged with material. Chips have formed at the tip of sharp shapes.
2. The material takes longer to remove than usual, you want to press more on the cutter to get results.
3. The attachment vibrates and causes a burning sensation when removing the coating.
4. Curvature of the nozzle. Cutters can become curved as a result of falls, long-term use, and be destroyed by aggressive disinfectants and high temperatures during sterilization. A curved nozzle hits the client's nail hard, becomes excessively hot due to vibrations, which reduces the service life of the device handle.

Characteristics