Staleks Pro EXPERT solid carbide milling cutter green corn, diameter 4 mm / working part 14 mm (FT90G040/14)

Staleks milling cutter corn hard alloy green EXPERT - all-metal tool of coarse hardness for hardware manicure and pedicure. The working part with coarse straight-transverse and cross-shaped notches. Hard-alloy attachments are distinguished by the fact that they cut the material, creating thin chips, and not dust.

Corn cutter Staleks TVS with green notch 4 mm is suitable for preparation for extension of artificial nails and correction of extensions, correction of the nail plate, removal of hard coatings. In pedicure/podology it is used for treatment of keratinized areas of skin, cleaning of calluses and corns.

Staleks EXPERT carbide milling cutter corn Green quickly removes gel polish coatings. During operation, the nozzle moves smoothly, without sudden movements and prolonged exposure to the same place. Carefully cuts the material, leaving a smooth surface.

The diameter of the shank is standard for a milling machine - 2.36 mm +/- 0.016 mm. The maximum permissible value of the rotation speed of the carbide nozzle on the milling machine for removing gel polish is up to 18,000 rpm. It is important to adhere to the recommendations for the number of revolutions for each type of cutter and procedure - working at high speeds can cause overheating of the cutter, injury to the client.

Optimal speed for performing manicure procedures:

• Natural nails and skin, thousand rpm: 5-10 - filing, reducing thickness, grinding, polishing; 10-15 - removing cuticles, grinding side ridges, cleaning pockets.
• Artificial nails, thousand rpm: 15-20 – thickness removal, nail removal with a milling cutter (gel), shaping; 20-25 – coating removal, design; 25-30 – free edge formation; more than 30 – individual types of design, other work.
• Pedicure, thousand rpm: 5-15 - removal of corns, skin polishing; 15-25 - cleaning cracks, removal of superficial calluses; 25-30 and more - work with core calluses, other types of work.

The carbide cutter Staleks corn coarse hardness EXPERT is safe when used correctly, is resistant to corrosion, and can be sterilized and disinfected in various ways, except for the use of disinfectant solutions based on active oxygen.

Staleks milling cutter corn solid carbide green EXPERT - features:

• purpose: hardware manicure and pedicure;
• shape: corn;
• material: stainless steel;
• green notch;
• size of the working part: length – 14 mm, diameter – 4 mm;
• recommended speed: up to 18 thousand revolutions per minute;
• service life: 4-6 months;
• corrosion resistance;
• withstands all types of disinfection and sterilization;
• in a package: 1 pc.

Corn cutter Staleks TVS with green notch 4 mm.

1. Choose a tool based on the type of area being treated: a cutter for removing extended nails, for removing cuticles, grinding, filing down the length, etc. It is important to follow the recommended number of revolutions for a specific cutter to avoid overheating the tool and injuring the client.
2. Do not throw or beat the nozzle - this may cause the rotation center to shift and lead to defects. It is impossible to use a deformed cutter for dusting extended nails.
3. Regularly check the nail file cutter and other attachments for correct centering visually or with a special tool.
4. When working, use gloves, safety glasses or a shield.

Cleaning carbide bits

Staleks Pro withstands all types of disinfection and sterilization (cold or hot).

• Remove the handle of the device immediately after use. Using a soft brush, carefully remove any remaining nail dust and other dirt. Try not to scratch the surface of the nozzle to avoid damage.
• To remove light dirt from the attachments, it is not recommended to rinse with running water using a brush, so as not to spread splashes with possible pathogens.
• Disinfection: Prepare a disinfectant solution and place the attachments according to the manufacturer's instructions for time and concentration. It is recommended to choose products that destroy hepatitis B, C and dermatomycosis viruses.
• Use a container with warm soapy water and a mild detergent. Place the attachments in the solution for 10-15 minutes to soften any remaining dirt. You can use an ultrasonic bath for a deeper pre-sterilization cleaning.
• Sterilization. Place the tips in sterilization bags intended for tendon or autoclave containers to avoid damage and ensure proper air or steam circulation. at 180°C for 60 minutes, 160°C for 150 minutes.
• Autoclave sterilization time: at 120°C, 1.1 atm. pressure for 45 minutes; 132°C, 2 atm. pressure - 20 minutes. After autoclave sterilization, it is recommended to leave the instrument for 1 hour to cool down, so that sudden temperature changes do not damage the nozzle.
• Regularly check the autoclave or tendon performance with biological indicators to ensure sterilization is effective.

Storage of carbide bits

• Store the nail trimmer and other attachments in a dry, clean condition, in a sterile, closed container. Choose a dry storage location to prevent rust and mold.
• Avoid getting moisture, dust, loose and abrasive substances between the working surfaces of the attachments.

When to change the tool

If carbide bits are used, stored and cleaned correctly, their functionality will remain for up to 4-6 months. The metal will not be covered with corrosion, and there will be no burrs or chips on the tip of sharp shapes.

When it's time to change attachments:

1. The work area has lost its shine, has become smooth in places or is clogged with material. Chips have formed at the tip of sharp shapes.
2. The material takes longer to remove than usual, you want to press more on the cutter to get results.
3. The attachment vibrates and causes a burning sensation when removing the coating.
4. Curvature of the nozzle. The TVS nail file cutter can become curved as a result of falls, long-term use, and be destroyed by aggressive disinfectants and high temperatures during sterilization. A curved nozzle knocks on the client's nail, becomes excessively hot due to vibration, which reduces the service life of the device handle.

Characteristics