Staleks Pro EXPERT carbide milling cutter, blue corn, diameter 4 mm / working part 14 mm (FT90B040/14)

Staleks PRO EXPERT carbide milling cutter corn blue - all-metal tool of medium abrasiveness and medium hardness. The working part with medium straight-transverse and cross-shaped notches. Carbide attachments are distinguished by the fact that they cut the material, creating chips, not dust.

The "corn" shape is suitable for correcting natural and artificial nails, as well as preparing for extensions, removing gel polish and other hard coatings.

The milling cutter for correcting extended nails carefully cuts the material and leaves a smooth surface. In pedicure/podology it is used to treat keratinized areas of the skin, clean calluses and corns.

Staleks PRO EXPERT TVS corn cutter with blue notch 4x14 mm quickly removes gel polish coatings, treats calluses and nails with fungus (onychomycosis). During operation, the cutter for removing gel polish gently moves along the edge of the nail, without sudden movements and prolonged exposure to the same place. Carefully cuts the material, leaving a smooth surface.

The diameter of the shank is standard for a milling machine - 2.36 mm +/- 0.016 mm. The maximum permissible value of the rotation speed of a carbide cutter for removing blue gel polish is up to 18,000 rpm. It is important to adhere to the recommendations for the number of revolutions for each type of cutter and procedure - working at high speeds can cause the cutter to overheat, injuring the client.

Optimal speed for performing manicure procedures:

• Natural nails and skin, thousand rpm: 5-10 - filing, reducing thickness, grinding, polishing; 10-15 - removing cuticles, grinding side ridges, cleaning pockets.
• Artificial nails, thousand rpm: 15-20 - thickness removal, shaping; 20-25 - coating removal, design; 25-30 - free edge formation; more than 30 - individual types of design, other work.
• Pedicure, thousand rpm: 5-15 - removal of corns, skin polishing; 15-25 - cleaning cracks, removal of superficial calluses; 25-30 and more - work with core calluses, other types of work.

Experienced manicurists and pedicurists are recommended to buy a cutter for removing gel polish, because it is safe when used correctly. The tool with a high-quality diamond coating is resistant to corrosion, can be sterilized and disinfected in various ways, except for the use of disinfectant solutions based on active oxygen.

Staleks PRO EXPERT solid carbide milling cutter corn blue.

• purpose: hardware manicure and pedicure;
• shape: corn;
• material: stainless steel;
• blue notch;
• size of the working part: length – 14 mm, diameter – 4 mm;
• recommended speed: up to 18 thousand revolutions per minute;
• service life: 4-6 months;
• corrosion resistance;
• withstands all types of disinfection and sterilization;
• in a package: 1 pc.

Staleks PRO EXPERT TVS milling cutter corn with blue notch 4x14 mm.

1. Choose a tool based on the type of area being processed: a cutter for filing under the nail, for removing cuticles, grinding, filing down the length, etc. It is important to follow the recommended number of revolutions for a specific cutter to avoid overheating the tool and injuring the client.
2. Do not throw or hit the attachment - this may cause the rotation center to shift and lead to defects. A deformed cutter cannot be used.
3. Regularly check the correct centering of the delamination cutter and other attachments visually or with a special tool.
4. When working, use gloves, safety glasses or a shield.

Cleaning carbide bits

Staleks Pro withstands all types of disinfection and sterilization (cold or hot).

• Remove the handle of the device immediately after use. Using a soft brush, carefully remove any remaining nail dust and other dirt. Try not to scratch the surface of the nozzle to avoid damage.
• To remove light dirt from the attachments, it is not recommended to rinse with running water using a brush, so as not to spread splashes with possible pathogens.
• Disinfection: Prepare a disinfectant solution and place the attachments according to the manufacturer's instructions for time and concentration. It is recommended to choose products that destroy hepatitis B, C and dermatomycosis viruses.
• Use a container with warm soapy water and a mild detergent. Place the attachments in the solution for 10-15 minutes to soften any remaining dirt. You can use an ultrasonic bath for a deeper pre-sterilization cleaning.
• Sterilization. Place the tips in sterilization bags intended for tendon or autoclave containers to avoid damage and ensure proper air or steam circulation. Sterilize at 180°C for 60 minutes, 160°C for 150 minutes.
• Autoclave sterilization time: at 120°C, 1.1 atm. pressure for 45 minutes; 132°C, 2 atm. pressure - 20 minutes. After autoclave sterilization, it is recommended to leave the instrument for 1 hour to cool down, so that sudden temperature changes do not damage the nozzle.
• Regularly check the autoclave or tendon performance with biological indicators to ensure sterilization is effective.

Storage of carbide bits

• Store the Blue Carbide Nail Polish Remover Corn in a dry, clean form, in a sterile, closed container. Choose a dry storage location to prevent rust and mold.
• Avoid getting moisture, dust, loose and abrasive substances between the working surfaces of the attachments.

When to change the tool

If carbide bits are used, stored and cleaned correctly, their functionality will remain for up to 4-6 months. The metal will not be covered with corrosion, and there will be no burrs or chips on the tip of sharp shapes.

When it's time to change attachments:

1. The working area has lost its abrasiveness, has become smooth in places or has become clogged with material. Chips have formed at the tip of sharp shapes.
2. The material takes longer to remove than usual, you want to press more on the cutter to get results.
3. The attachment vibrates and causes a burning sensation when removing the coating.
4. Curvature of the nozzle. The TVS cutter can become curved as a result of falls, long-term use, and be destroyed by aggressive disinfectants and high temperatures during sterilization. A curved nozzle knocks on the client's nail, becomes excessively hot due to vibration, which reduces the service life of the device handle.

Characteristics