Staleks Pro EXPERT solid carbide cutter, hard black cone, diameter 6 mm/working part 14 mm (FT110H060/14)

Carbide cone cutter with black notch for hardware manicure and pedicure Staleks Pro EXPERT is a solid metal tool of high abrasiveness and rigidity. The working part has a large straight transverse and cross-shaped notch. Carbide attachments are distinguished by the fact that they cut the material, creating chips, not dust.

The "cone" shaped cutter is suitable for correcting natural and extended nails, as well as for preparing for extension, removing gel polish and other hard coatings. The attachment carefully cuts the material and leaves a smooth surface. In pedicure/podology, it is used to treat keratinized areas of the skin, clean calluses and corns. During operation, the cutter for removing extended nails moves gently along the edge of the plate, without sudden movements and prolonged action on the same place.

The shank diameter is standard for a milling machine – 2.36 mm. The maximum permissible value of the rotation speed of the carbide attachment is up to 6000 rpm. It is important to adhere to the recommendations for the number of revolutions for a certain type of cutters and procedures, since working at high speeds can cause overheating of the tool and injury to the client.

Optimal speed for performing manicure procedures:

• Natural nails and skin, thousand rpm: 5-10 - filing, reducing thickness, grinding, polishing; 10-15 - removing cuticles, grinding side ridges, cleaning pockets.
• Artificial nails, thousands of rpm: 15-20 - thickness removal, shaping; 20-25 - coating removal, design; 25-30 - free edge formation; more than 30 - individual types of design, other work.
• Pedicure, thousand rpm: 5-15 – removal of calluses, skin polishing; 15-25 – cleaning cracks, removal of superficial calluses; 25-30 and more – work with core calluses, other types of work.

It is recommended to buy a cutter for removing gel polish cone with a black notch for experienced and novice nail masters, because it is safe when used correctly. The cutter is resistant to corrosion, it can be sterilized and disinfected in various ways, except for the use of disinfectant solutions based on active oxygen.

Carbide cone cutter with black notches for hardware manicure and pedicure Staleks Pro EXPERT - features:

• purpose: hardware manicure and pedicure;
• coarse abrasive;
• cone shape;
• material: stainless steel;
• size of the working part: length – 14 mm, diameter – 6 mm;
• recommended speed: up to 6000 rpm;
• service life: 4-6 months;
• black corrosion-resistant gel polish remover;
• withstands all types of disinfection and sterilization;
• in a package: 1 pc.

Nozzle for milling cutter for removing gel polish TVS milling cutter Staleks About coarse cones EXPERT 6 x 14 mm: application

1. Choose a tool based on the type of area being treated: for lifting the cuticle, filing the length, grinding the skin around the nail, etc. It is also important to follow the recommended number of revolutions for a specific cutter to avoid overheating the tool and injuring the client.
2. Do not throw or hit the attachment - this may cause the rotation center to shift and cause defects. A deformed cutter is not used.
3. If you buy a cone cutter for manicure, you should regularly check its correct centering visually or with a special tool.
4. When working, use gloves, safety glasses or a shield.

Cleaning carbide bits

The nozzle for the milling cutter for removing gel polish TVS milling cutter O cone of rough hardness EXPERT 6x14 mm withstands all types of disinfection and sterilization (cold or hot).

• Remove the handle of the device immediately after use. Using a soft brush, carefully remove any remaining nail dust and other dirt. Try not to scratch the surface of the cutter to avoid damage.
• To remove light dirt, it is not recommended to rinse the nozzle with running water using a brush, so as not to spread splashes with possible pathogens.
• Disinfection: Prepare a disinfectant solution and dip the attachments according to the manufacturer's instructions for time and concentration. It is recommended to choose products that destroy hepatitis B, C and dermatomycosis viruses.
• Use a container with warm soapy water and a mild detergent. Dip the burrs in the solution for 10-15 minutes to soften any remaining dirt. You can use an ultrasonic bath for a deeper pre-sterilization cleaning.
• Sterilization. Place the tips in sterilization bags intended for tendon or autoclave containers to avoid damage and ensure proper air or steam circulation. at 180°C for 60 minutes, 160°C for 150 minutes.
• Autoclave sterilization time: at 120°C, 1.1 atm. pressure for 45 minutes; 132°C, 2 atm. pressure - 20 minutes. After autoclave sterilization, it is recommended to leave the instrument for 1 hour to cool down, so that sudden temperature changes do not damage the nozzle.
• Regularly check the autoclave or tendon performance with biological indicators to ensure sterilization is effective.

Storage of carbide bits

• The Staleks Pro EXPERT carbide nail polish remover cone is stored in a clean, dry form, in a sterile, closed container. Choose a dry storage location to prevent rust and mold from appearing.
• Avoid getting moisture, dust, loose and abrasive substances between the working surfaces of the cutter.

When to change the tool

If the carbide cutter for removing the length of the nail is used correctly, stored and cleaned, then its functionality will remain up to 4-6 months. The metal will not be covered with corrosion, and there will be no burrs or chips on the tip of the sharp forms.

1. The working area has lost its abrasiveness, has become smooth in places or has become clogged with material. Chips have formed at the tip of sharp shapes.
2. The material takes longer to remove than usual, you want to press more on the cutter to get results.
3. The nail file vibrates and causes a burning sensation when removing the coating.
4. Curvature of the nozzle. The TVS cutter can become curved as a result of falls, long-term use, and be destroyed by aggressive disinfectants and high temperatures during sterilization. A curved nozzle knocks on the client's nail, becomes excessively hot due to vibration, which reduces the service life of the device handle.

Characteristics