Mirror nail powder Kodi №01, 3g

Technology for applying mirror powder No. 1.

Mirror Powder No. 1 can be applied in several ways. Depending on the chosen application option, the result will be different every time: from the effect of pure silver to a variety of shades.

Method 1.

1.Standardly prepare the nail plate for applying gel polish, apply RubberBaseGel, dry for 2 minutes in a UV lamp or 30 seconds in LED.

2.Apply Gel Polish No. 100 BW in two thin layers, drying each layer for 2 minutes in a UV lamp or 30 seconds in LED.

3. With an eyeshadow applicator or just with your finger (ring finger), spread the mirror powder and rub into the color until a mirror shine.

4. Fix in UV lamp for 1 minute or 15 seconds in LED.

5. Overlap the RubberTop Gel design with two thin coats, sealing the ends of the free edge well and drying each coat for 2 minutes in a UV lamp or 30 seconds in an LED.

Note: for maximum wearability of the powder, it is necessary to remove its excess from the end of the free edge. To do this, carefully work with a soft buff (abrasive 180 * 220) on the end. After that, seal.

6. Using a special Cleanser, remove the dispersion layer. Design is ready!

Method 2.

1.Standardly prepare the nail plate for applying gel polish, apply Rubber Base Gel, dry for 2 minutes in a UV lamp or 30 seconds in LED.

2. Apply gel polish No. 100 BW in two thin layers, drying each layer for 2 minutes in a UV lamp or 30 seconds in LED. Remove the dispersion layer using a special Cleanser.

3. With an applicator for applying shadows or just with your finger (ring finger), spread the mirror powder over the sticky layer and rub into the color until a mirror shine.

4. Fix in UV lamp for 1 minute or 15 seconds in LED.

5. Overlap the Rubber TopGel design with two thin coats, sealing the ends of the free edge well and drying each coat for 2 minutes in a UV lamp or 30 seconds in an LED.

Note: for maximum wearability of the powder, it is necessary to remove its excess from the end of the free edge. To do this, carefully work with a soft buff (abrasive 180 * 220) on the end. After that, seal.

6. Using a special Cleanser, remove the dispersion layer. Design is ready!

Method 3. The effect of pure silver.

1.Standardly prepare the nail plate for applying gel polish, apply RubberBaseGel, dry for 2 minutes in a UV lamp or 30 seconds in LED.

2. Apply gel polish No. 30 M in two thin layers, drying each layer for 2 minutes in a UV lamp or 30 seconds in LED. Remove the dispersion layer using a special Cleanser.

3. With an applicator for applying shadows or just with your finger (ring finger), spread the mirror powder over the sticky layer and rub into the color until a mirror shine.

4. Fix in UV lamp for 1 minute or 15 seconds in LED.

5. Overlap the RubberTopGel design with two thin coats, sealing the ends of the free edge well and drying each coat for 2 minutes in a UV lamp or 30 seconds in an LED.

Note: for maximum wearability of the powder, it is necessary to remove its excess from the end of the free edge. To do this, carefully work with a soft buff (abrasive 180 * 220) on the end. After that, seal.

6. Using a special Cleanser, remove the dispersion layer. Design is ready!

Method 4. Rose-purple silver effect.

1.Standardly prepare the nail plate for applying gel polish, apply RubberBaseGel, dry for 2 minutes in a UV lamp or 30 seconds in LED.

2. Apply gel polish No. 40 LC in two thin layers, drying each layer for 2 minutes in a UV lamp or 30 seconds in LED. Remove the dispersion layer using a special Cleanser.

3. With an applicator for applying shadows or just with your finger (ring finger), spread the mirror powder over the sticky layer and rub into the color until a mirror shine.

4. Fix in UV lamp for 1 minute or 15 seconds in LED.

5. Overlap the RubberTopGel design with two thin coats, sealing the ends of the free edge well and drying each coat for 2 minutes in a UV lamp or 30 seconds in an LED.

Note: for maximum wearability of the powder, it is necessary to remove its excess from the end of the free edge. To do this, carefully work with a soft buff (abrasive 180 * 220) on the end. After that, seal.

6. Using a special Cleanser, remove the dispersion layer. Design is ready!

Mirror Powder No. 1 can also be applied to the gel polishes of the Crystal collection, both with and without a sticky layer. Each time you will receive new shades of coverage. If the nail plate is thin, we recommend strengthening it with a base gel for maximum wearability of the powder.